Wait for the X32 Core to be available and put it next to your DAW. The X32 Core will have the same recording features as the X32, so you can run a short USB/FW cable between DAW and X32 Core. Between...
Type: Posts; User: Peter van Gils
Wait for the X32 Core to be available and put it next to your DAW. The X32 Core will have the same recording features as the X32, so you can run a short USB/FW cable between DAW and X32 Core. Between...
My point was that in the live "warzone" anything can happen, eg somebody unplugs something (power, signal and/or aes50) while your amps are powered on. You may be doing everything to prevent this,...
My opinion: put a dcx2496 in every amprack (I have 3). It allows you to use the ampracks without the X32 and makes the setup more fool proof and more robust. If you rely on the X32, then pops and...
+1 !
James, yes, it will work as you described: if you assign a bus to one of the local aouts and send that set of aouts to the S16, you will have the signal at both places.
Todd, you must be confused....
James,
Just a warning: Most intercom systems put a DC voltage (not the same as phantom power!) on the line to power the intercom units. This might (will?) kill the inputs/outputs of your...
Marc, why don't you turn off confirmations in the setup menu? ... ;-)
;-) not a real "solution"
It seems that if you reboot the Airport Express after the X32 has booted, all works fine (at least for me).
I'm doing a theatre show soon with a lot of condensor mics. So a lot of phantom power LEDs will be on on my S16s. These LEDs are bright!! Too bright! So, I have to make sure that the LEDs are not...
I like to mix monitor/IEMs from FOH using the sends-on-faders, but that requires a lot of button presses (select sends-on-faders, select right bus layer, select bus, select input layer, adjust...
I tried this, but I can not get Capture to recognize the X32. (Mountain Lion using firewire on MBP, latest Capture, tried UC 1.7 as well as the oldest supporting Mountain Lion.) Any tips welcome! I...
DMX is 250kbit/s and would require 125kHz analog bandwidth. Next to that DMX uses voltages that might kill an analog input.
So, a 48kHz digital connection (with <24kHz analog bandwidth) will not...
The idea is to use submixes, but you already knew that. Other point of view: why is 8 DCAs sufficient for FOH mixing? In other words 16 should be more than enough for iem mixes.
If you really want...
If you have 2 S16s you can send different sets of signals to the P16 outs of AES50 port A and B...
Gerrit,
I've tested my S16s with cheap procab cat60 cable (>80m) with >5 ethercon connections in between and, currently, it's working fine (X32 is master, 48kHz). In the beginning I had connection...
Hi Tim,
Is the purpose of the audience mics recording the applause? Then you might want to setup the mics near the stage because of the delay you would get in the recorded audience signal...
I think that with "redundant network provisions", they are probably referring to the error correction code: for this to work, redundant data is send across the network. Or, it's a future feature...
Select the playback channels and go to the sends tab in the menu. There you can set the send tap per channel. Note that the tap is selected per 2 mixbusses!
Hi Fiona,
Huh? You're right, the ethercons are indeed from Neutrik, but it seems that their quality is a bit less than the NE8FDPs I bought for the panels in my racks. Oh well, I'm not going to...
Jim,
I did it similar. D-hole plate on the front of my racks with 2x NE8FDP. On the cables I use NE8MC - if I remember correctly - with Neutrik RJ45s.
At the mixer side I use a short ethercon...
I have a X32 and 2x S16. I noticed that some of the pins in the EtherCons of the AES50 ports might slip back (partially) into the connector housings. This ofcourse results in bad connections, sync...
The X32 has guitar effects built in, the SL does not... ;-)
+1 ... I'm also moving from SL24 to X32.
Why?
- Number of channels
- Digital snake
- Number of subgroups / DCAs
- Routing flexibility
The new SL32 is for me the example that Presonus did...
That does not protect your expensive gear from "operator errors". My opinion: use a DI if you're not 100% sure the output can handle phantom power... (Yes, I do not have female jack to male xlr...
