You are here: Home » Forum
BEHRINGER_Billboard-XD80USB

Search:

Type: Posts; User: Gary Baker

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    8
    Views
    282

    Nicholas - Can you be more specific about what's...

    Nicholas - Can you be more specific about what's not working with those Aux's? Just dead? I haven't experienced this that I know of, but if it's specific aspects of the Aux that's not working, and...
  2. As long as they make all the faders available...

    As long as they make all the faders available within the protocol, it should work for any DAW that is compatible. I was just being sarcastic throwing another DAW out there.
  3. Yes! Except I'm on Cubase. ;-)

    Yes! Except I'm on Cubase. ;-)
  4. Replies
    7
    Views
    472

    Yeah...At 50m, I'm out. I rarely need more than...

    Yeah...At 50m, I'm out. I rarely need more than 25 feet. I keep the Rack right near stage and mix from the iPad.
  5. I been using the matrix crossovers for about a...

    I been using the matrix crossovers for about a year and a half now, no problems. I upgrade firmware within a week or two of the release. Craig's thoughts sound logical. Probably ought to contact...
  6. Thread: Routing

    by Gary Baker
    Replies
    9
    Views
    250

    If you want to send two bus's to the same output,...

    If you want to send two bus's to the same output, you'd have to send each bus to the same matrix first, and then assign the Matrix to a physical output. Unless I'm misunderstanding your question,...
  7. Replies
    15
    Views
    474

    Hi Randy. If you're talking about the analog...

    Hi Randy.

    If you're talking about the analog output assignments on the routing page (like Nick suggested), it's just a routing assignment to a physical output. So for instance, instead of...
  8. Replies
    15
    Views
    474

    Hi Randy. What I was referring to is selecting...

    Hi Randy.

    What I was referring to is selecting a mix bus as the source for a mixer channel. So if you go into a mixer channel, on the config page you can select the source for that channel. The...
  9. Replies
    15
    Views
    474

    Hi Randy. Actually, you can send a Bus mix to...

    Hi Randy.

    Actually, you can send a Bus mix to another Bus, however, not directly and you have to burn an additional channel (two if it's a stereo Bus). Once you have your Bus mix set, you can...
  10. When I bought my first X32, I looked at the...

    When I bought my first X32, I looked at the Roland stuff as well (the "M" series). That was almost two years ago so I don't remember exactly, but I believe the Roland stuff was around double the...
  11. Replies
    14
    Views
    636

    Although I rarely run into a situation where the...

    Although I rarely run into a situation where the low cut on an individual channel is a problem for the monitors, I'm with Gary...You really want monitor sends to be pre-EQ. The stage is a completely...
  12. Replies
    12
    Views
    678

    If you only need something to put the X32 on, and...

    If you only need something to put the X32 on, and no additional workspace, a simple, double-braced X type of keyboard stand works fine. Just make sure it's double braced.
  13. I have a full console and two Racks. All three...

    I have a full console and two Racks. All three get significantly more road use than in the studio, but that's because most of my in-studio recording is done at 88.2. If I had a 44.1 project,...
  14. Hi Karl. Since you're new to the forum, your...

    Hi Karl.

    Since you're new to the forum, your posts are still on a delay. Your second post came through after my first post.

    As far as comparing the full console to the compact, it really boils...
  15. For studio use, the first thing I would note is...

    For studio use, the first thing I would note is that the X32 is limited to sample rates of 44.1 and 48. If you have a need for other sample rates, the X32 won't work. Second, the pre's and...
  16. Hi Brandon. I'm not sitting in front of my X32...

    Hi Brandon.

    I'm not sitting in front of my X32 right now, but if you save your scene and email it to me, I'll load it up and see if I can give you any pointers. I don't know if you can send...
  17. Brian - Why would you *not* want the ability to...

    Brian - Why would you *not* want the ability to adjust the pan of a mono signal going into a stereo bus?
  18. Glenn - All of the above. Most often though, I'm...

    Glenn - All of the above. Most often though, I'm using the P16M with IEM's, and running direct channel taps, normally pre-EQ since the P16's have channel EQ's. Unless of course, there needs to be...
  19. Replies
    7
    Views
    476

    James - If changing scenes fixes the problem...

    James - If changing scenes fixes the problem (without changing cables/connections), that would lead me to believe that the problem is in the scene parameters and not in the X32, S16, or the...
  20. Replies
    7
    Views
    476

    X32 Rack-S16 CAT connection

    Hey all.

    Ran into something strange at a show last night. Had everything set up and getting ready to dial the system in. X32 Rack and S16 both showing connectivity and sync, but no audio passing...
  21. Replies
    5
    Views
    383

    Yeah...I was rather surprised when I got the...

    Yeah...I was rather surprised when I got the first X32, at how limited the MIDI capabilities were. There was very little (actually almost zero if memory serves) documentation on the MIDI...
  22. Replies
    5
    Views
    438

    Makes perfect sense Paul. I just didn't think it...

    Makes perfect sense Paul. I just didn't think it through quite as far as you did, and assumed he had extra inputs to play with.
  23. Replies
    5
    Views
    438

    Paul - Maybe I misunderstood the question. Why...

    Paul - Maybe I misunderstood the question. Why not just change the source for a given channel to a local input as needed? That way you can have what you want where you want it, without having to go...
  24. It sounds like you just need to set up the...

    It sounds like you just need to set up the routing properly on the X32. In the routing section, "card out" is where you assign the interface card output.
  25. Replies
    5
    Views
    438

    Yes. In the routing section, things are done in...

    Yes. In the routing section, things are done in blocks of 8, however on each individual channel's config page, you can select the source for that channel.
Results 1 to 25 of 151
Page 1 of 7 1 2 3 4