You are here: Home » Forum
BEHRINGER_Billboard-XD80USB

Search:

Type: Posts; User: Tim Padrick

Page 1 of 13 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    36
    Views
    822

    Send the drop back. You'll be forever cursing...

    Send the drop back. You'll be forever cursing that you got only 25', and only 8 channels. Use your existing snake - the 4 returns will be handy for IEMs or powered wedges.
  2. Replies
    16
    Views
    505

    The X-Air boxes might be a more economical way to...

    The X-Air boxes might be a more economical way to fulfill your needs.
  3. Replies
    43
    Views
    1,497

    I can't imagine why console DCAs are not set up...

    I can't imagine why console DCAs are not set up to move the faders of the assigned channels, so that when one has the channels on the surface, the effect of the DCA on the channel can be readily...
  4. Replies
    4
    Views
    157

    Make sure that the FX are set to 100% wet. ...

    Make sure that the FX are set to 100% wet.

    Make sure that the FX returns are not turned up in buses 13-16.
  5. If you have the same model router for your rig as...

    If you have the same model router for your rig as for at home, make sure that you set them up with different IP address ranges so you can test your rig router at home without having to shut down the...
  6. If the channels with only 1/4" ins have gain...

    If the channels with only 1/4" ins have gain controls, you may be able to use them on very loud sources such as drums (you'll have to max the gain or close to it). I've done this on several...
  7. Here's an example - ignore what you don't need.

    Here's an example - ignore what you don't need.
  8. Replies
    6
    Views
    172

    Channels or buses (e.g. Aux Sends)? There's no...

    Channels or buses (e.g. Aux Sends)? There's no need for a graphic on a channel (99.99% of the time anyway).
  9. Replies
    9
    Views
    169

    Make sure that the Wet/Dry on the FX is 100% wet....

    Make sure that the Wet/Dry on the FX is 100% wet.

    Make sure that the returns are not dialed into bus 13.
  10. Make your you did not accidentally plug into the...

    Make your you did not accidentally plug into the line jack. It happens.
  11. Replies
    18
    Views
    580

    The router's manual will tell you the IP address...

    The router's manual will tell you the IP address as it came from the factory. There are several common factory defaults. You can use the default, or change it.

    Here's a sample network (just...
  12. Replies
    8
    Views
    750

    If you want rubbery feeling fader caps, shoot...

    If you want rubbery feeling fader caps, shoot them with this: http://www.homedepot.com/p/Performix-Brand-11-oz-Plasti-Dip-Black-Rubber-Coating-Spray-11203-6/100131010
  13. Except for the lift in and out of the truck (and...

    Except for the lift in and out of the truck (and stairs), you can make messing with the big mixer easier by mounting the case to a Rigid AC9945 saw stand - works like a hand truck, and with a push it...
  14. Let the FX come back into the returns, in stereo,...

    Let the FX come back into the returns, in stereo, as normal. Then put each pair of returns on its own DCA, as well as the Vocal on a DCA and the tracks on a DCA.
  15. Replies
    5
    Views
    183

    If it does not like your fingertips, use your...

    If it does not like your fingertips, use your knuckles. Or your right pinky tip.
  16. Search the forums here. You'll find some threads...

    Search the forums here. You'll find some threads about routing to P16s.
  17. Tape and sharpie is fine if you have a single...

    Tape and sharpie is fine if you have a single layer. Gets a bit tricky when you have two, and really tough when you have three (If I could write small enough to denote three layers on a piece of...
  18. Replies
    11
    Views
    827

    I expect that all preamps will measure the same. ...

    I expect that all preamps will measure the same. The reason is that our test signals are infinitely less complex than music.
  19. Don't forget that the subs' filters cause a lot...

    Don't forget that the subs' filters cause a lot of delay. So if the tops are properly delayed to the subs, your system will likely be behind the vocals already.
  20. Replies
    11
    Views
    447

    Two schools of thought: Set it to the resonant...

    Two schools of thought:

    Set it to the resonant frequency of the drum. This will make it 'more sensitive', which is good if you have a drummer who plays with dynamics.

    If dynamics are not...
  21. Replies
    11
    Views
    447

    Turn on the filter. Put on your headphones and...

    Turn on the filter. Put on your headphones and select key cue, adjust the filter to the frequency you want, then turn off the key cue. (The manual is very poor in this area.)
  22. An expansion would decrease the low level...

    An expansion would decrease the low level signals, not increase them. It's usually used to cut stage noise in vocal mics when there's no one speaking, or if you have a channel with some low level...
  23. Replies
    12
    Views
    726

    IMHO, with most speakers, with regard to the...

    IMHO, with most speakers, with regard to the calculated max level, you take off 6dB for power compression, 6dB for "sounds like crap if you run it any louder", and in some cases even more for the...
  24. This is for monitors, but it does pertain to the...

    This is for monitors, but it does pertain to the house system as well:

    Keep in mind when ringing out monitors, you must duplicate the performance situation. Ringing out with an open stage...
  25. What you have working is how I would expect to...

    What you have working is how I would expect to have to do it.

    You could save some snippets or scenes to change the appropriate channel(s) monitoring from "tape" to input for overdubbing on various...
Results 1 to 25 of 302
Page 1 of 13 1 2 3 4