You are here: Home » Forum

Search:

Type: Posts; User: Gary Baker

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    11
    Views
    234

    Although I rarely run into a situation where the...

    Although I rarely run into a situation where the low cut on an individual channel is a problem for the monitors, I'm with Gary...You really want monitor sends to be pre-EQ. The stage is a completely...
  2. Replies
    12
    Views
    560

    If you only need something to put the X32 on, and...

    If you only need something to put the X32 on, and no additional workspace, a simple, double-braced X type of keyboard stand works fine. Just make sure it's double braced.
  3. I have a full console and two Racks. All three...

    I have a full console and two Racks. All three get significantly more road use than in the studio, but that's because most of my in-studio recording is done at 88.2. If I had a 44.1 project,...
  4. Hi Karl. Since you're new to the forum, your...

    Hi Karl.

    Since you're new to the forum, your posts are still on a delay. Your second post came through after my first post.

    As far as comparing the full console to the compact, it really boils...
  5. For studio use, the first thing I would note is...

    For studio use, the first thing I would note is that the X32 is limited to sample rates of 44.1 and 48. If you have a need for other sample rates, the X32 won't work. Second, the pre's and...
  6. Hi Brandon. I'm not sitting in front of my X32...

    Hi Brandon.

    I'm not sitting in front of my X32 right now, but if you save your scene and email it to me, I'll load it up and see if I can give you any pointers. I don't know if you can send...
  7. Brian - Why would you *not* want the ability to...

    Brian - Why would you *not* want the ability to adjust the pan of a mono signal going into a stereo bus?
  8. Glenn - All of the above. Most often though, I'm...

    Glenn - All of the above. Most often though, I'm using the P16M with IEM's, and running direct channel taps, normally pre-EQ since the P16's have channel EQ's. Unless of course, there needs to be...
  9. Replies
    7
    Views
    379

    James - If changing scenes fixes the problem...

    James - If changing scenes fixes the problem (without changing cables/connections), that would lead me to believe that the problem is in the scene parameters and not in the X32, S16, or the...
  10. Replies
    7
    Views
    379

    X32 Rack-S16 CAT connection

    Hey all.

    Ran into something strange at a show last night. Had everything set up and getting ready to dial the system in. X32 Rack and S16 both showing connectivity and sync, but no audio passing...
  11. Replies
    5
    Views
    299

    Yeah...I was rather surprised when I got the...

    Yeah...I was rather surprised when I got the first X32, at how limited the MIDI capabilities were. There was very little (actually almost zero if memory serves) documentation on the MIDI...
  12. Replies
    5
    Views
    325

    Makes perfect sense Paul. I just didn't think it...

    Makes perfect sense Paul. I just didn't think it through quite as far as you did, and assumed he had extra inputs to play with.
  13. Replies
    5
    Views
    325

    Paul - Maybe I misunderstood the question. Why...

    Paul - Maybe I misunderstood the question. Why not just change the source for a given channel to a local input as needed? That way you can have what you want where you want it, without having to go...
  14. It sounds like you just need to set up the...

    It sounds like you just need to set up the routing properly on the X32. In the routing section, "card out" is where you assign the interface card output.
  15. Replies
    5
    Views
    325

    Yes. In the routing section, things are done in...

    Yes. In the routing section, things are done in blocks of 8, however on each individual channel's config page, you can select the source for that channel.
  16. Replies
    53
    Views
    2,505

    Boy, I'm sure glad I'm so busy mixing shows that...

    Boy, I'm sure glad I'm so busy mixing shows that I don't have time for hair splitting and debating semantics! LOL
  17. Replies
    20
    Views
    1,961

    Kevin - Sorry dude...But if you had a bad X32 out...

    Kevin - Sorry dude...But if you had a bad X32 out of the box, and didn't address it right then and there, you have no one to blame but yourself.
  18. Replies
    20
    Views
    1,961

    I'm going to meet Jeff halfway on this one. I've...

    I'm going to meet Jeff halfway on this one. I've had plenty of gear over the years where the manufacturer did a "swap" with me for a warranty repair issue, so I understand where he's coming from. ...
  19. It's definitely something connected to the new...

    It's definitely something connected to the new firmware or new iPad app version...Or a combination. I have the lag in iPad display update when I'm standing right next to the router, with full WiFi...
  20. Replies
    12
    Views
    904

    Scott - Just to clarify, you said the iPad "sees"...

    Scott - Just to clarify, you said the iPad "sees" the wireless, I assume you mean it's connecting as well? I'm trying to determine if the problem is between the iPad and router, or between the...
  21. Replies
    3
    Views
    201

    I'm not sure what your signal source is, but why...

    I'm not sure what your signal source is, but why would you want to *insert* a preamp? Why not run the raw signal straight to the pre, and then from the pre into an aux in?
  22. Replies
    10
    Views
    644

    The P16 channel assignments are in the routing...

    The P16 channel assignments are in the routing tab/section.
  23. Replies
    7
    Views
    633

    This won't be much help, but it sounds like it's...

    This won't be much help, but it sounds like it's a setup/routing issue within Studio One. That being said, I don't use Studio One, so I'm useless to you. I assume you've have the proper driver for...
  24. Thread: New to X32

    by Gary Baker
    Replies
    11
    Views
    934

    Bob - I've been running X32 gear (I have two...

    Bob - I've been running X32 gear (I have two Racks, on full console, and two S16's) for over a year now. Probably in the realm of 60 or so gigs, and I also use them often for band practice. I've...
  25. Thread: New to X32

    by Gary Baker
    Replies
    11
    Views
    934

    Hi Bob. Welcome to the board. There are a...

    Hi Bob. Welcome to the board.

    There are a couple of ways to accomplish what you want. What I typically do, is send the main outs to matrix's, and split things from there. So for instance, if...
Results 1 to 25 of 141
Page 1 of 6 1 2 3 4