You are here: Home » Forum
BEHRINGER_Billboard-XD80USB

Search:

Type: Posts; User: Dan Tarbill

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    12
    Views
    1,847

    I just checked the release notes on 2.10. It...

    I just checked the release notes on 2.10. It doesn't mention anything about the USB recording shutdown fix. Is there a more complete bug fix list available somewhere?
  2. I'd take a look at the ROUTING page on your X32...

    I'd take a look at the ROUTING page on your X32 and see what it shows as being connected on AES50 A. If it shows an X32 rather than 2 S16's...the problem might be at the X32 end.

    In any case, you...
  3. Replies
    7
    Views
    224

    The sticking Mute Group buttons is a known...

    The sticking Mute Group buttons is a known failure mode. I think I've heard tell that newer versions of the board have done something to address the problem.
  4. In the US, B&H and Full Compass are listing these...

    In the US, B&H and Full Compass are listing these for $1,199.00 USD...but they aren't showing them as being available yet.

    Will these support the same 44.1 & 48 kHz sampling rates as the S16...or...
  5. (Sadly) We are still using the same "ruggedized"...

    (Sadly) We are still using the same "ruggedized" but apparently non-shielded cable on the B port on a weekly basis and haven't had a problem...so I doubt that just the act of plugging in a...
  6. A non-shielded cable can leave the port...

    A non-shielded cable can leave the port susceptible to a static discharge hitting the port and damaging it. You are correct in saying that they didn't use the term "burn out". I was perhaps...
  7. Unfortunately, burning out the AES50 A port is a...

    Unfortunately, burning out the AES50 A port is a common failure mode. Behringer has implicated the use of non-shielded Cat5 cable as a possible culprit. (I have yet to see a mention here of the B...
  8. So...how do you solo a channel on the headphones...

    So...how do you solo a channel on the headphones on the iPad?
  9. Somewhat related to the original poster's...

    Somewhat related to the original poster's question...

    I'd like to be able to configure the ins and outs of the X-UF USB driver in a DAW (i.e. SONAR in my case) without actually having the X-32...
  10. Replies
    27
    Views
    2,863

    (pointless bump)

    (pointless bump)
  11. Replies
    27
    Views
    2,863

    Anyone using SQUARE WAVE UPS's with X32?

    Ok...let me refine my question...

    Is anyone successfully using UPS's with a SQUARE WAVE output with their X32 equipment?

    I did a bit more research and became a LOT more confused...

    In the...
  12. Replies
    27
    Views
    2,863

    Anyone using UPS's on their X32 system?

    This is from a thread a kinda highjacked...

    http://forum.behringer.com/showthread.php?2999-loss-of-connectivity-and-audio-plops


    In an attempt to head off future connectivity issues, we...
  13. Replies
    11
    Views
    1,439

    We've had connectivity issues also. We've gone...

    We've had connectivity issues also. We've gone to a ruggedized Ethercon Cat5e from Sound Ideas. I'm not sure if that really fixed the issue, but we've not had the pops we were having when someone...
  14. Replies
    30
    Views
    3,683

    >QUESTION 1. Has anyone had any connectivity...

    >QUESTION 1. Has anyone had any connectivity problems between an X32 Rack and an S16?

    I can't speak to the X32 Rack...but I can say that I've had a spontaneous problem with our X32 board suddenly...
  15. Replies
    15
    Views
    1,647

    We are having a similar issue. It had been...

    We are having a similar issue. It had been working without any problems for nearly a year. Then one Sunday AM (when I wasn't there) the S16 and the X32 refuse to sync.

    Hoping that the S16 was...
  16. Replies
    1
    Views
    641

    X32 Producer Dimensions

    It seems more than a little odd that the X32 Producer is being reported as "shipping", yet there are still no dimensions available to indicate simple things like "will this thing fit in my rack". ...
  17. Replies
    22
    Views
    4,129

    Actually FLAC and OGG are lousy substitutes. ...

    Actually FLAC and OGG are lousy substitutes. They may be great formats on their own...but the question isn't about what is a technically good format...it's about what format everyone uses and shows...
  18. Replies
    570
    Views
    106,577

    Sticky: Missing samples in USB recording

    I have a 2 hour recording done off the mains to a USB stick from Sunday morning (04/21/13). I haven't listened to the entire recording front to back, but I did happen to notice a couple of incidents...
  19. Replies
    6
    Views
    1,204

    I would seriously consider replacing my studio's...

    I would seriously consider replacing my studio's aging Yamaha 01v with the X32 Producer if it would support 88.2 and/or 96 kHz. Being "restricted" to 16 inputs (at that sample rate) wouldn't be an...
  20. Replies
    24
    Views
    8,488

    Thanks for the details.

    Thanks for the details.
  21. Replies
    24
    Views
    8,488

    I think you missed the point of my performance...

    I think you missed the point of my performance question. Would my suggestion of continually appending to the recording file so you don't lose everything when the recording isn't terminated properly,...
  22. Replies
    24
    Views
    8,488

    Hitting STOP makes this work. However...I...

    Hitting STOP makes this work.

    However...I still maintain that this function is far more frail than it needs to be.

    Every second or so (on a low priority thread)...
    open
    append
    close

    That...
  23. Replies
    24
    Views
    8,488

    So...you're not going to admit that the number of...

    So...you're not going to admit that the number of people who are having issues with this function indicates that there may be a way that you could do this better?
  24. Replies
    24
    Views
    8,488

    If there wasn't a signal source selected that had...

    If there wasn't a signal source selected that had an actual signal...I would expect that you would get a large file that only contained digital zeroes...not a zero byte file.

    It's actually sort of...
  25. Replies
    24
    Views
    8,488

    I have made the recorder work...but I have yet to...

    I have made the recorder work...but I have yet to successfully record something I needed to keep. The first time (v1.11), I just powered the board off and failed to stop the recorder. The second...
Results 1 to 25 of 30
Page 1 of 2 1 2