You are here: Home » Forum

Search:

Type: Posts; User: Gary Baker

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Glenn - All of the above. Most often though, I'm...

    Glenn - All of the above. Most often though, I'm using the P16M with IEM's, and running direct channel taps, normally pre-EQ since the P16's have channel EQ's. Unless of course, there needs to be...
  2. Replies
    7
    Views
    182

    James - If changing scenes fixes the problem...

    James - If changing scenes fixes the problem (without changing cables/connections), that would lead me to believe that the problem is in the scene parameters and not in the X32, S16, or the...
  3. Replies
    7
    Views
    182

    X32 Rack-S16 CAT connection

    Hey all.

    Ran into something strange at a show last night. Had everything set up and getting ready to dial the system in. X32 Rack and S16 both showing connectivity and sync, but no audio passing...
  4. Replies
    5
    Views
    167

    Yeah...I was rather surprised when I got the...

    Yeah...I was rather surprised when I got the first X32, at how limited the MIDI capabilities were. There was very little (actually almost zero if memory serves) documentation on the MIDI...
  5. Replies
    5
    Views
    233

    Makes perfect sense Paul. I just didn't think it...

    Makes perfect sense Paul. I just didn't think it through quite as far as you did, and assumed he had extra inputs to play with.
  6. Replies
    5
    Views
    233

    Paul - Maybe I misunderstood the question. Why...

    Paul - Maybe I misunderstood the question. Why not just change the source for a given channel to a local input as needed? That way you can have what you want where you want it, without having to go...
  7. It sounds like you just need to set up the...

    It sounds like you just need to set up the routing properly on the X32. In the routing section, "card out" is where you assign the interface card output.
  8. Replies
    5
    Views
    233

    Yes. In the routing section, things are done in...

    Yes. In the routing section, things are done in blocks of 8, however on each individual channel's config page, you can select the source for that channel.
  9. Replies
    53
    Views
    1,953

    Boy, I'm sure glad I'm so busy mixing shows that...

    Boy, I'm sure glad I'm so busy mixing shows that I don't have time for hair splitting and debating semantics! LOL
  10. Replies
    20
    Views
    1,760

    Kevin - Sorry dude...But if you had a bad X32 out...

    Kevin - Sorry dude...But if you had a bad X32 out of the box, and didn't address it right then and there, you have no one to blame but yourself.
  11. Replies
    20
    Views
    1,760

    I'm going to meet Jeff halfway on this one. I've...

    I'm going to meet Jeff halfway on this one. I've had plenty of gear over the years where the manufacturer did a "swap" with me for a warranty repair issue, so I understand where he's coming from. ...
  12. It's definitely something connected to the new...

    It's definitely something connected to the new firmware or new iPad app version...Or a combination. I have the lag in iPad display update when I'm standing right next to the router, with full WiFi...
  13. Replies
    12
    Views
    743

    Scott - Just to clarify, you said the iPad "sees"...

    Scott - Just to clarify, you said the iPad "sees" the wireless, I assume you mean it's connecting as well? I'm trying to determine if the problem is between the iPad and router, or between the...
  14. Replies
    3
    Views
    158

    I'm not sure what your signal source is, but why...

    I'm not sure what your signal source is, but why would you want to *insert* a preamp? Why not run the raw signal straight to the pre, and then from the pre into an aux in?
  15. Replies
    10
    Views
    511

    The P16 channel assignments are in the routing...

    The P16 channel assignments are in the routing tab/section.
  16. Replies
    7
    Views
    541

    This won't be much help, but it sounds like it's...

    This won't be much help, but it sounds like it's a setup/routing issue within Studio One. That being said, I don't use Studio One, so I'm useless to you. I assume you've have the proper driver for...
  17. Thread: New to X32

    by Gary Baker
    Replies
    11
    Views
    774

    Bob - I've been running X32 gear (I have two...

    Bob - I've been running X32 gear (I have two Racks, on full console, and two S16's) for over a year now. Probably in the realm of 60 or so gigs, and I also use them often for band practice. I've...
  18. Thread: New to X32

    by Gary Baker
    Replies
    11
    Views
    774

    Hi Bob. Welcome to the board. There are a...

    Hi Bob. Welcome to the board.

    There are a couple of ways to accomplish what you want. What I typically do, is send the main outs to matrix's, and split things from there. So for instance, if...
  19. Replies
    12
    Views
    828

    It's a limitation of the X32. I have no idea why...

    It's a limitation of the X32. I have no idea why they limited it to 8 faders, but I'd be curious to know.
  20. Replies
    12
    Views
    828

    Are you looking to *control* Cubase with the X32,...

    Are you looking to *control* Cubase with the X32, or are you looking to send your audio tracks from Cubase to the X32 and mix within the X32? If you're looking to use the X32 as a control surface,...
  21. Replies
    12
    Views
    828

    Len - I missed this post somehow, or I would've...

    Len - I missed this post somehow, or I would've responded. I use Cubase, but I started out with 6 and am now on 7.5...Should be a similar setup to 5 though.

    The X32 is not my primary interface in...
  22. Ivan - I think you may be over thinking it, and...

    Ivan - I think you may be over thinking it, and getting caught up on the term "insert".

    In the scenarios you list above (or any scenario where you don't need to utilize the X32's pre), don't...
  23. A few random thoughts Ivan, in no particular...

    A few random thoughts Ivan, in no particular order...

    1. Since you're talking about essentially setting your studio up around the X32, keep in mind that the X32 only operates at 44.1k and 48k...
  24. Ever since I upgraded to 2.04 (and subsequently...

    Ever since I upgraded to 2.04 (and subsequently 2.05), the redraw response on the iPad app has been shakey at best. The actual control doesn't seem to be impacted, just the display. It happens...
  25. Replies
    20
    Views
    1,417

    I recently picked a couple of Sandisk Cruzer Fit...

    I recently picked a couple of Sandisk Cruzer Fit sticks. Low profile, doesn't stick out very far. Both are 16 gigs, and both work fine in my Racks and in my full console. The only thing I've found...
Results 1 to 25 of 134
Page 1 of 6 1 2 3 4