You are here: Home » Forum

Search:

Type: Posts; User: Peter van Gils

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    542

    What George explained will work, but you will...

    What George explained will work, but you will have to play around yourself and get acquainted with the routing settings. You will need a pen and paper to write down what is on what channel on which...
  2. Replies
    8
    Views
    542

    You don't need the ADAT cards. You can already...

    You don't need the ADAT cards. You can already achieve this out-of-the-box using the AES50 routing...
  3. Function clash: mono bus as fx bus and "safe levels"

    I use the mono/center bus as an fx send bus to save a mixbus. I got several scenes nicely setup to add some reverb to vocals by default via the mono bus. All well until I reboot the board: no...
  4. Replies
    28
    Views
    1,056

    Hi Per, good to hear you got your rack up and...

    Hi Per, good to hear you got your rack up and running again! ;-)
    In all situations I had no audio through the X32, it was an operator error (yep, mine).
    The syncing can be a bit peculiar though....
  5. Replies
    28
    Views
    1,056

    Hmm. Yesterday I wanted to upgrade my X32 and...

    Hmm. Yesterday I wanted to upgrade my X32 and core to 2.05. I didn't wire the AES ports, so when I booted my X32 with 2.04 it didn't get a clock (my X32 is clocked via AES by default): red indication...
  6. The problem is probably not the amount of code,...

    The problem is probably not the amount of code, but the amount of memory to store the samples for 16+6=22 channels @ 48kHz
  7. Replies
    88
    Views
    3,821

    What do you define as master or slave? :) I would...

    What do you define as master or slave? :) I would only use the terms master/slave for clocking, but that is not related to the HA control.

    I would say: enable HA remote on the X32 that should to...
  8. Replies
    88
    Views
    3,821

    I can confirm that it works similar with a X32...

    I can confirm that it works similar with a X32 full, X32 core and 2 S16's.

    My connections:
    X32 FOH --> X32 core --> S16 --> S16.
    The X32 core and S16s live on stage.
    The X32 core is used for...
  9. Replies
    0
    Views
    157

    v2.04 mono bus compressor bug

    Found a bug:
    Send a signal through the X32 (to main LR and matrix busses), but not to the mono/center bus.
    Next, select the mono/center bus and show the compressor tab on the screen.
    The blue dot...
  10. Replies
    3
    Views
    389

    Be aware that there is an incompatibility on the...

    Be aware that there is an incompatibility on the wired connection between airport express and the x32: the connection fails very often. Probably the auto-sensing fails (10/100/1000Mbps and...
  11. Yes ;-) you don't need to use the mix busses (I...

    Yes ;-) you don't need to use the mix busses (I like to keep my mix busses free for other purposes: 6 wedge mixes, 8 IEM mixes and 2 fx busses).

    Use the M/C bus as the sub-bus.
    Make sure that...
  12. I'm afraid so if I read this in the release...

    I'm afraid so if I read this in the release notes:
    "The new HA Gain Remote option allows console gains to be remote controlled by another console (e.g. for using X32 RACK as a Digital Snake)".
    But...
  13. There is an additional new feature in v2.0x that...

    There is an additional new feature in v2.0x that allows you to control the headamps of a X32 remotely, eg to use a X32 rack as a S16. Question remains whether this new feature also allows you to...
  14. I know that it will be possible to control the...

    I know that it will be possible to control the headamps of a X32 full/compact/producer/rack from another X32 by enabling remote headamp control with v2.0x, but will it also be possible to control an...
  15. Headamp control of S16 "behind" X32 Core with v2.0x

    I could not find an answer to the question below:

    I have the following setup / AES50 connections:
    FOH: X32 full <--> Stage: X32 core <--> S16 <--> S16 (+ 8 additional ADAT outs)

    The X32 full...
  16. Replies
    5
    Views
    393

    As far as I can see in the video below (at...

    As far as I can see in the video below (at 12:18), it's a CR2032.
    http://youtu.be/en84LnnGmjE
  17. Replies
    5
    Views
    393

    Same issue here: if the board has been in storage...

    Same issue here: if the board has been in storage for some time, the time is off by minutes to hours. My board is stored at approx. 15 degrees Celcius; maybe this is too cold for the battery powering...
  18. What about assigning one of the user-assignable...

    What about assigning one of the user-assignable buttons to the tap delay? ;-) Works flawless!
  19. Please, tell me where I can find these Airplay...

    Please, tell me where I can find these Airplay adapters (preferably integrated in a router so it fits in the back of my X32 road case).
    I don't want to setup my laptop on all gigs: there's not...
  20. I think you're drawing conclusions too fast....

    I think you're drawing conclusions too fast. There are order of magnitudes more Airport Expresses on the street than X32s: if there would be a structural issue with the Airport it would have Apple's...
  21. Ok, did some tests with X32 and Airport Express...

    Ok, did some tests with X32 and Airport Express (the current flat model with power cable and 5GHz support, NOT the old plug-in type):
    - Airport firmware version 7.6.4, there is no option in the...
  22. Ok, will try when I have my desk (and Airport)...

    Ok, will try when I have my desk (and Airport) setup (currently in storage).

    That's a misconception I think: there have been intermittent wifi issues with some of the firmware versions, but the...
  23. To be clear: sometimes my X32 is working with the...

    To be clear: sometimes my X32 is working with the Airport Express, sometimes I need to reconnect the X32 ethernet to get it working.
    I know that a straight cable should work (always, and not...
  24. I'm also using an Apple Airport Express (because...

    I'm also using an Apple Airport Express (because I like the Airplay feature) and, indeed, there is an issue getting the X32 to talk to the Airport. I think the issue is on the ethernet connection...
  25. Replies
    9
    Views
    635

    Routing and sync source are separate things: -...

    Routing and sync source are separate things:
    - Sync source only defines which device provides the clock. In a digital system you need 1 clock (and not more) to prevent that one of the devices would...
Results 1 to 25 of 66
Page 1 of 3 1 2 3