You are here: Home » Forum

Search:

Type: Posts; User: Anthony Martin

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Faders are often replaced individually! If one...

    Faders are often replaced individually! If one fails, you only need to replace the defective fader, not a multitude of them. They are, however, sold in groups of five (5) if the Behringer web site...
  2. Replies
    5
    Views
    120

    Using X32-Edit, after you select the "MUTE GRP"...

    Using X32-Edit, after you select the "MUTE GRP" button to the right of the display, select (single-left-click w/ your mouse) on the Mute Group you want to set up, and select which channels (or bus or...
  3. Is there a hardware restriction (limitation) that...

    Is there a hardware restriction (limitation) that prevents independent Mixbus configurations (pre/post, etc) or was the odd-even pairing a arbitrary selection made by programmers?
  4. Replies
    3
    Views
    116

    That would only change the color of the scribble...

    That would only change the color of the scribble strip. If the Bus Sends bar on the channel HOME tab is gray, it means that particular Bus send is muted for that particular channel. See post below.
  5. Replies
    3
    Views
    116

    If the bar is gray, it means that send for that...

    If the bar is gray, it means that send for that particular channel is muted on that channel's "sends" tab. If you are using X32-Edit, go to the channel "sends" tab and de-select the "Mute" button...
  6. If I were flying around, carrying limited...

    If I were flying around, carrying limited production with me (X32-Rack, S19, & IEMs in a small "aircraft-friendly" rack), I doubt if I would also carry a backup rack. In the event of failure, there...
  7. Replies
    12
    Views
    791

    There continues to be quite a bit of confusion...

    There continues to be quite a bit of confusion with the use of shielded Cat5e cables for use with the Behringer X32 consoles & the S16 DigitaL Snakes.

    First, Behringer has stated on numerous...
  8. Replies
    5
    Views
    287

    Generally, we crossover 18" subs around 90-110Hz,...

    Generally, we crossover 18" subs around 90-110Hz, depending on the specific subs. Don't neglect using the channel lo-cut filters, especially for vocals--it helps to keep the vocals out of the subs.
  9. Change adjacent-Mixbus pairing to independent Mixbus setup

    Recently prepped for a show where the X32 was not approved for mixing monitors only because of the way in which the X32 handles the Mixbus configurations--the paired Mixbus scenario. I had to put up...
  10. I must have missed something. What is "fat...

    I must have missed something. What is "fat channel view"?
  11. Replies
    11
    Views
    633

    You can measure all day using pink noise (or...

    You can measure all day using pink noise (or white) and there are still many parameters that you simply cannot measure. For example, the way a Midas preamp sounds as you saturate it . . . remember...
  12. I don't know what your budget is but I would...

    I don't know what your budget is but I would check out Extron's USB Extender and USB Extender Plus devices. They are active devices and are designed for the professional AV market with up to 480...
  13. There is not a crossover in the X32. Some users...

    There is not a crossover in the X32. Some users do use the output filtering to send their outputs to sub & "tops" but a true loudspeaker management system does a lot more than that--phasing, timing,...
  14. "Ringing" a poorly designed sound system is, at...

    "Ringing" a poorly designed sound system is, at best, problematic! More often than not, ringing a poorly designed sound system results in a loss of system gain & dynamics, not to mention the tonal...
  15. Using X32-Edit PC on my Motion Computing Tablet,...

    Using X32-Edit PC on my Motion Computing Tablet, the application does utilize the stylus & touch screen--beats an iPad any day!
  16. Replies
    25
    Views
    1,263

    Sticky: Poll: Hard mute! The mute now makes no sense. When I...

    Hard mute! The mute now makes no sense. When I mute a channel individually, often times it's for a pretty specific reason, whether it be an open vocal mic I need to mute or a bad signal from the...
  17. Replies
    39
    Views
    2,483

    I realize that we're off topic but my APC...

    I realize that we're off topic but my APC Smart-UPS is ALWAYS providing output through the UPS system--there is no "switching" as you suggest with a time lag. System reliability is a concern for me...
  18. According to Behringer, the standard to use...

    According to Behringer, the standard to use should be TIA/EIA-568B. Practically speaking, though, either standard would work as long as both ends are wired to the same standard (in theory). ...
  19. Replies
    39
    Views
    2,483

    That's funny, Per. Sort of puts stage security...

    That's funny, Per. Sort of puts stage security in a new light!
  20. Replies
    39
    Views
    2,483

    A number of Pro Audio manufacturers have...

    A number of Pro Audio manufacturers have recommended that the DSPs only be connected to UPSs with true sine wave outputs. It has to do with the switch-mode power supplies in these units and their...
  21. Replies
    39
    Views
    2,483

    Kev, considering the price of the X32 at just...

    Kev, considering the price of the X32 at just over $2500 MAPP, I wouldn't expect to have an appropriate UPS "embedded" or "built in" to the X32. The UPS that I use costs me between $400.00 & $600.00...
  22. If you add a 2nd S16, you can have all 16 outputs...

    If you add a 2nd S16, you can have all 16 outputs from the X32-Rack and 8 outputs from the X32-Full (at FOH) routed via AES50 show up on stage by:

    routing at FOH AES50A Outputs 17-25 >> AES50...
  23. Replies
    6
    Views
    504

    I would replace the fader--they're inexpensive. ...

    I would replace the fader--they're inexpensive. Any "cleaning" would require partial disassembly of the X32. Sounds like something has gotten into the mechanism, slowing down the movement...
  24. Replies
    3
    Views
    269

    As per Care support, the AES50B ports on the S16...

    As per Care support, the AES50B ports on the S16 Digital Snakes are only used to daisy chain S16s. I would think that you would need to connect the DN9650 to the AES50B port on whichever X32 console...
  25. Replies
    4
    Views
    296

    Purchase real shielded Cat5e that is designed to...

    Purchase real shielded Cat5e that is designed to be trampled over, spilled on, etc. If the specs of the cable are not listed, then, chances are, it won't hold up for long. I have used the Belden...
Results 1 to 25 of 164
Page 1 of 7 1 2 3 4