You are here: Home » Forum

Search:

Type: Posts; User: Nick Davis

Page 1 of 19 1 2 3 4

Search: Search took 0.02 seconds.

  1. out of interest what were you running your output...

    out of interest what were you running your output level at on the main l/r meters?
  2. Thanks - beginning to think this must be the case...

    Thanks - beginning to think this must be the case - which makes sense

    (haven't really used the mono bus and thought the M/C dependent should link the L/R and output fader - but was then getting a...
  3. Thanks for the replies. Evan - no did not mean...

    Thanks for the replies.
    Evan - no did not mean just send kick etc to sub but All ch routed to l/r as well.
    Looked into using m/c and although the level of a send can follow the l/r send the actual...
  4. Best way to set up an Aux (Matrix) fed sub?

    I usually for simplicity sake use an active system where by I feed the main L/R to the subs which have a filtered crossover out that feed the active tops that also have a HPF (Low cut) filter that...
  5. Replies
    3
    Views
    147

    the x32 and s16 (same) do accept line level...

    the x32 and s16 (same) do accept line level inputs - though a di is recommended -
    see the SOS review of the X32
  6. Replies
    0
    Views
    115

    sort of part of the family!

    Anyone from MG or anyone know when the Turbosound IQ series will be hitting the shelves (UK & Europe).
    Tried emailing TS but bounced back.
  7. I understand from release notes and info from...

    I understand from release notes and info from behringer that the answer is No
  8. i do not think you can contol the head amp of...

    i do not think you can contol the head amp of another x32 from another. what you can do in v2 is set the headamps on the x32 controlling the heads.ps ( with good headroom) and then go intl a "split"...
  9. I am quite interested in the new turbosound IQ...

    I am quite interested in the new turbosound IQ series speakers ( though cannot see any stockists in UK - for pre-orders) - there is some DSP to model other speakers - does anyone know which ones ( or...
  10. or you could send your monitoring signal to a bus...

    or you could send your monitoring signal to a bus pair and then route this bus to a pair aux outs ( or two main outs) and connect your monitors to these. The bus pair controlling the level of your...
  11. what effect do you have loaded in FX 4?

    what effect do you have loaded in FX 4?
  12. I thought the Ql1 was about $6000 - must have got...

    I thought the Ql1 was about $6000 - must have got it wrong
  13. For many the buying decision may well be the ...

    For many the buying decision may well be the "genuine" midas preamps plus also the build quality and external style of the M32 compared to the x32 - specifically the quality of the chassis, the...
  14. I too have just reused old printer cables had...

    I too have just reused old printer cables had lying around - but no problems
    Clicks possibly originate from other source.
  15. personally I always reboot with safe main levels ...

    personally I always reboot with safe main levels - often tend to have one Dca to control all Faders that way the main l/r can always be set / reset at unity.
  16. Replies
    9
    Views
    334

    yes tap is direct off pres as it should be- if...

    yes tap is direct off pres as it should be- if you want to include processing ( but why?) go via P 16 outs.
  17. Why worry! Midas, klarke Technique and Turbosound...

    Why worry! Midas, klarke Technique and Turbosound are now part of the Music Group "family" and integration will undoubtedly increase e.g the v2 firmware now allows remote control of the soon to be...
  18. Replies
    4
    Views
    303

    Yes Glen- we all know this ! The question was...

    Yes Glen- we all know this ! The question was simply how it actually works - maybe academic in most cases - but just want definitive clarity on how it works.
    ( & plus if would never occur is the...
  19. Replies
    4
    Views
    303

    yes - not a big issue just interested to resolve...

    yes - not a big issue just interested to resolve how the process works - think I am correct in my understanding but then again maybe not.
  20. Replies
    4
    Views
    192

    This has been pointed out to Behringer loads of...

    This has been pointed out to Behringer loads of times on different forums - uncertain if it tis the combination of 8.1 and 64 bit - hopefully they will have looked into it and solved for the v2.0...
  21. Replies
    4
    Views
    303

    The State of things

    There was some discussion a week or so a go on other forums on how the saving of the console state works especially if there is an unforeseen outage and reboot of the console. Although, sudden...
  22. But Oleg is saying his DCA faders are also all...

    But Oleg is saying his DCA faders are also all the way down - I don't recall "safe main level" doing this and doesn't for me
  23. have to slightly disagree - the same basic...

    have to slightly disagree - the same basic platform / workflow and processing options. It would seem they are both built upon same internal hardware layout as is clearly evidenced by the physical...
  24. Replies
    93
    Views
    9,299

    I am not sure behringer have given a definite...

    I am not sure behringer have given a definite date for any release - even v2.0 itself.
  25. Replies
    19
    Views
    764

    yes..when first got x32 this is how I connected...

    yes..when first got x32 this is how I connected xcontrol as it was called.
    You can also have a "direct" and wireless connection via a router.
Results 1 to 25 of 472
Page 1 of 19 1 2 3 4