You are here: Home » Forum

Search:

Type: Posts; User: George Dougherty

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    11
    Views
    278

    That's what the system Eq is for, to compensate...

    That's what the system Eq is for, to compensate for overall EQ issues in the room and allow for as "normal" an EQ as possible on the channel strip. In small rooms, cutting the low end until the...
  2. Replies
    9
    Views
    628

    9-18 Update to X32 Edit is still no bueno.

    9-18 Update to X32 Edit is still no bueno.
  3. Replies
    4
    Views
    640

    No problem.. Thanks for doing that. The odd thing...

    No problem.. Thanks for doing that. The odd thing is that I created them in the latest version of x32 edit and exported them from there. At least I think it was the latest version of x32 edit.
  4. Sounds like a hardware issue to me. Firmware is...

    Sounds like a hardware issue to me. Firmware is initialized after everything powers up.
  5. Replies
    6
    Views
    772

    There aren't any major changes that would cause...

    There aren't any major changes that would cause it not to function. Works just fine in demo mode here.
  6. Replies
    7
    Views
    495

    Yes, check an M7 for channel move, link options...

    Yes, check an M7 for channel move, link options and take a page from there please...
  7. Replies
    17
    Views
    1,012

    The one I have is fairly inexpensive at ~$150. 4...

    The one I have is fairly inexpensive at ~$150. 4 battery outlets, 2+ surge only outlets. I've had no problems with it on battery, but that's mostly during teardown when everything else is powered...
  8. Replies
    17
    Views
    1,012

    Makes the rack heavier but I put a Cyberpower...

    Makes the rack heavier but I put a Cyberpower 500VA 1U ups in with mine. Highly recommended.
  9. I put all my vocal fx on a DCA and use it to...

    I put all my vocal fx on a DCA and use it to quickly and smoothly fade out fx between songs. Mute groups control mute states of the source channels. Vocals route to a subgroup for parallel...
  10. Replies
    5
    Views
    314

    You should strongly consider switching to a P16...

    You should strongly consider switching to a P16 setup for monitors. While you don't get all channels, it's far more robust and convenient with each unit being powered from the distribution hub. In...
  11. Replies
    17
    Views
    1,284

    The DR260 limiters should be set via a meter at...

    The DR260 limiters should be set via a meter at the amp outputs measuring voltage to protect the speaker drivers. Overall volume limiting should be set via policy and consequences. More than likely...
  12. Replies
    34
    Views
    2,748

    I do find when I get a freeze that often...

    I do find when I get a freeze that often switching tabs across the top and back to where I want gets things to resync.
  13. Replies
    34
    Views
    2,748

    Most stability issues are the fault of the router...

    Most stability issues are the fault of the router and wireless connection rather than the software. I have more problems the further I go and the more that's going on. I'm just glad I have at least...
  14. Replies
    17
    Views
    1,284

    Dont want clipping out of the X32 outputs. Gain...

    Dont want clipping out of the X32 outputs. Gain staging is too hot in that case. You're clipping in the digital domain there and the result is not beneficial even if the Driverack has a limiter. ...
  15. Replies
    0
    Views
    131

    Head amp gain following

    I have a full x-32 I use with a band. Band owns it. Have all my channels arranged and normally run 1:1 with my physical inputs.

    I own a rack and S16. I occasionally use my S16 as an onstage...
  16. Replies
    8
    Views
    357

    You will not take the mixbus direct to p16's and...

    You will not take the mixbus direct to p16's and get reverb. That's your unprocessed signal. The fx returns are your wet channels.
  17. Replies
    3
    Views
    388

    VEQ is "vintage" and has a variable Q as the gain...

    VEQ is "vintage" and has a variable Q as the gain is adjusted. That operation is in line with a more traditional analog EQ response.
  18. iOS 7 IS required for the latest app which works...

    iOS 7 IS required for the latest app which works properly with the latest firmware. Get updated and you'll be fine. At least the ipad 2 supports iOS 7...
  19. Replies
    26
    Views
    4,003

    Another reason you want a canopy is that LCD...

    Another reason you want a canopy is that LCD screens tend to fade when they get hot. Direct sunlight , coupled with max brightness just increases the heat the LCD must deal with and exacerbates the...
  20. Replies
    4
    Views
    267

    Cyberpower makes a decently lightweight UPS (for...

    Cyberpower makes a decently lightweight UPS (for a UPS) in the 450VA range that will easily run a Rack and network gear for 15-20min. If you don't have a UPS, you need one.
  21. You're backwards. The matrix is not a mixbus. ...

    You're backwards. The matrix is not a mixbus. It's a submix of only the L/R and mixbuses, designed to feed other outputs separate from the main L/R.

    So you submix the drums and add them on top...
  22. The only other thing that could be doing it would...

    The only other thing that could be doing it would be for an input channel with it's fader up (send to Main L/R) to be taking its input source from your aux bus. In that case you should also be...
  23. Replies
    6
    Views
    341

    Have you tried going backwards? Link the two S16...

    Have you tried going backwards? Link the two S16 as normal (1-8B -> 9-16A and then use the B on the 9-16 S16? If that doesn't work, then I think a snippet to change your routing (swap your 1-8 outs...
  24. Your Main tab with the Mix 3 selected should not...

    Your Main tab with the Mix 3 selected should not have the LR send engaged. That's what it sounds like is going on.
  25. Replies
    13
    Views
    712

    I thought the intake was on the underside of the...

    I thought the intake was on the underside of the desk and any casing needed to take that into account. Possibly the tablecloth is getting sucked up against the bottom and preventing cooling airflow?
Results 1 to 25 of 141
Page 1 of 6 1 2 3 4